# Show an elevation model as shaded relief under your boundaries

Bring in a digital elevation model and see it as shaded relief with a colour ramp, with your own areas drawn on top.

Video: Show an elevation model as shaded relief under your boundaries (1 min 13 s): /images/docs/videos/elevation-on-a-map.mp4

## Best for

Anyone who wants to see the lie of the land under their areas: planners, flood and drainage officers, park and estate managers, consultants setting the scene for a report. You end up with an elevation layer you can switch to 3D, under boundaries from your own library.

**The example in this guide** is a real elevation model of the central Lake District, from Windermere up to Helvellyn: a GeoTIFF of ground heights, 1,024 by 1,024 pixels, each about 22 m across, 514 km² in all. On top go the area's electoral ward boundaries (Office for National Statistics, December 2025), already in the Library. Every ask below is written for that file, and results vary in the detail from one run to the next.

## What you need

- **An elevation file:** a GeoTIFF or another raster format (see [Upload imagery](/docs/your-data/imagery)).
- **A Creator or Creator Max seat.** Imagery is on paid seats.

## Before you start

- **Imagery is for showing, not for analysis.** Mapstack displays elevation and lets you read heights from it, but it does not calculate from it: no statistics per area, no slope, no flood modelling. If you have heights per area from elsewhere, bring them as a table and they can be mapped.

## The prompt

> This is an elevation model of the central Lake District. Show it as shaded relief with an elevation colour ramp, tell me the lowest and highest heights and the vertical units, and put the ward boundaries from my library on top.

## What to expect

1. **Your file becomes an imagery item**

   Mapstack reads the file and keeps it in your Library as imagery of the elevation kind. Its facts are on its **Details** tab.

2. **It makes the map**

   The elevation is shown as colour and relief, with a key in metres and a switch to 3D. The colours are stretched over all but the very lowest and highest heights, so they spread across the land: in the example the key runs from 39 m to 817 m, while the file's own heights run from 38 m at the head of Windermere to 949 m on Helvellyn. Boundaries from your Library are drawn on top, with their names, without uploading them again.

   ![Example: the central Lake District as colour and shaded relief, with its electoral wards from the Library on top. Helvellyn, the highest ground in the file, sits on the line between the Keswick and Greystoke and Ullswater wards.](/images/docs/elevation-on-a-map/lake-district-relief-with-wards.jpeg)

3. **It says what the file does not**

   Where the file leaves something unstated, such as the units its heights are in, Mapstack says so and where its answer comes from: the file itself, the published specification of the source, or you. Tell it what you know, in the conversation or in **Settings**, and that is what it uses.

## Common questions

**Can I get heights, slope or flood figures for each area?**

No. Mapstack shows elevation but does not calculate from it: no statistics per area, no slope, no flood modelling. You can read heights on the map and switch to 3D, and heights per area you bring as a table can be mapped.

**Where are the lowest and highest heights?**

On the imagery's **Details** tab, or ask for them, as the example did. The key's two ends are not the extremes: in the example it reads 39 m to 817 m, while the file reaches 949 m on Helvellyn.

**How do I know what units the heights are in?**

Ask. Where the file does not record something, Mapstack says so and where its answer comes from. If you know the units, say them and Mapstack uses them.

**Can I use boundaries already in my Library?**

Yes. Name them, for example "put the ward boundaries from my library on top", and they are drawn over the elevation without uploading them again.

## Related

- [Put aerial, satellite or elevation imagery on a map](https://mapstack.io/docs/your-data/imagery.md)
- [Make a map](https://mapstack.io/docs/make/maps.md)
